Friday, May 10, 2019

Prestige 143BP Remote Programming Instructions

This Pursuit PRO9644E system uses replacement remote: 143BP, ELVATTNB


1. Turn the ignition key to the on position.
2. Press and Release the Valet/Programming switch 3 times (Siren Chirps).
3. Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren.
4. Turn the ignition switch off.

The above action programs the Lock, Unlock, Start/Trunk, and Option 1 buttons which are typical for most systems. For additional channel programming beyond the 1 option button, you can use any unused button or combination of buttons not in use. In other words, to access option channel 5, 6, 7, you would do the following: From step 3 above:

a. Press and Release the Valet/Programming button 4 additional times to get to channel 5, then Press any unused transmitter button or button combination to program.

b. From step a, Press and Release the Valet/Programming button 1 time to get to channel 6, then Press any unused transmitter button or button combination to program.

c. From step b, Press and Release the Valet/Programming button 1 time to get to channel 7, then Press any unused transmitter button or button combination to program.

NOTE: Not all systems have channels above 3, check with your installation center for options your system may or may not have.

This remote has the ability to operate 2 Audiovox Alarms From A Single Transmitter. To toggle on and off vehicle one or two,,, Press the Trunk/Key button + the Lock button for 5 seconds. The LED flashes 2 times. Release the buttons, to select 2nd vehicle mode. Program this transmitter into the second vehicle's system. Any time you are in 2nd vehicle when the transmitter is operated, the LED will flash twice for each function. When in the prime vehicle mode, the LED will flash once for each function.

If you can't find your valet switch click here.

Thursday, March 7, 2019

Audiovox Pursuit PRO92BT PRO2T Keyless Remote Programming Instructions

Audiovox Pursuit PRO92BT PRO2T Remote
PROGRAMMING INSTRUCTIONS:

1. Enter the vehicle, and turn the ignition key to the "on" position.
2. Move the valet/bypass switch on - off - on - off- on then off.
3. The dash L.E.D. will flash one time, and the siren will "chirp" one time, indicating the system is ready to accept programming for channel 1, or the arm/disarm and panic functions.
4. You can assign any of the three transmitter button functions listed below to channel 1:
a) Pressing button #1 on the keychain transmitter.
b) Pressing button #2 on the keychain transmitter.
c) Pressing both buttons simultaneously on the keychain transmitter.

5 Press and hold the selected choice a, b, or c above, until the siren emits a long "chirp" to confirm that programming of channel I was successful.
6. Move the valet/bypass switch on, and then off again.
7. The dash mounted L. E. D. will flash 2 times and the siren will "chirp" one time, indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc.
8. You can assign anyone of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2.
9. Press and hold the selected choice. The siren will emit a long "chirp" to confirm that programming of channel 2 was successful.
10. Move the valet/bypass switch on, and then off again.
11. The dash mounted L.E.D. will flash 3 times and the siren will "chirp" one time, indicating that
the system is ready to accept programming for channel 3.
12. Press and hold the remaining transmitter button function. The siren will emit a long "chirp" to confirm that programming of channel 3 was successful.
13. To exit program mode, either turn the ignition key to the off position, or move the valet switch
on then off one additional time. This is indicated by a long "chirp" from the siren.

NOTE: If you can't find a valet switch click here.

Saturday, March 2, 2019

Astrostart AF-RF K5225 2-Way Remote Programming Instructions

This Astrostart AF-RF K5225 system uses replacement remote: EZSDEI7701

EZSDEI7701 Replacement Remote
EZSDEI7701 Remote

Please Note: The system can only store up to 4 remotes in it's memory. Your old remotes will be deleted from the system's memory right after a new remote has been programmed. In that case, after programming a new remote you will need to reprogram your existing ones to the system.

1. Open the hood. 2. Put the key in the ignition and turn it to RUN position.
3. Apply the brake once.
4. You now have 10 seconds to turn the key from RUN to STOP position 3 times.
5. If this sequence is correctly carried out, the control module flashes parking lights.
6. Press any button on the new remote control (except the panic button).


Note: Parking lights will flash one time once the new remote has been programmed.

7. To program your exisitng/old remotes (up to 4) you will need to start from step 1 to 6.
8. Apply the brake to turn off the programming mode.
9. You may now test all your remotes.


If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Astrostart RSS-2205A 2-Way Remote Programming Instructions

This Astrostart RSS-2205A system uses replacement remote: EZSDEI7701

EZSDEI7701 Replacement Remote
EZSDEI7701 Remote

NOTE: This system only accepts up to 4 remotes in it's memory. Your old remotes will be deleted from the system's memory once a new remote has been programmed. In that case, after programming a new remote you will need to reprogram your existing ones to the system.

1. Open the hood.
2. Put the key in the ignition and turn it to RUN position.
3. Apply the brake once.
4. Turn the key in the ignition from RUN to STOP position 3 times within 10 seconds.
5. If you have done the steps right, the system will flash the parking lights.
6. Press any button on the new remote (except the panic button).

(Parking lights will flash one time indicating that the new remote has been programmed.)

7. To program your exisitng/old remotes (up to 4) you will need to start from step 1 to 6.
8. Apply the brake to turn off the programming mode.
9. You may now test all your remotes.

If you can't find a valet switch click here.

Astrostart RSS-5224 2-Way Remote Programming Instructions

This Astrostart RSS-5224 system uses replacement remote: EZSDEI7701

EZSDEI7701 Replacement Remote
EZSDEI7701 Remote

Four different remote controls can be programmed for a given vehicle. If a 5th remote is added the 1st is deleted. When the first code learned command is sent, all the old codes are cleared. Therefore, if you want to add a new remote, all the old ones must be programmed as well.

1. Open hood.
2. Place key in ignition and turn to RUN position.

3. Apply the brake once.
4. You now have 10 seconds to turn the key from RUN to STOP position 3 times.
5. If this sequence is correctly carried out, the control module flashes parking lights.
6. Press any button on the new remote control (except the panic button).


When access code of new remote is memorized, the control module will respond with 1 flash of the parking lights.

7. Repeat the above procedures for each remote control that has to be programmed, up to four remotes.
8. Apply the brake.
9. New remotes are ready and now added to the system.


If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.