Monday, September 24, 2018

Crimestopper FS-80 Remote Programming Instructions

This Crimestopper FS-80 system uses replacement remote: FSSK-60, CHX433TX

The system can program a maximum of 4 remotes in it's memory and once it's in programming mode it will reset it's memory so make sure to program your existing remotes as well.

1. Turn the key in the ignition to ON position. (Pink wire must be connected and do not start the engine.)
2. Press the valet button 4 times.
3. After a few seconds the unit Chirps, Siren, Horn and Flashes the parking lights 4 times.
4. Press the LOCK button. You should get 1 Chirp/Honk indicating the first remote is coded, and then press button #1 of a second transmitter, the unit will Chirp/Honk twice indicating the second remote is coded and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise tum key off.
5. The system will Chirp/Honk 4 times when exiting learning mode.

If you can't find your valet switch click here.

Crimestopper FS-60 Remote Programming Instructions

This Crimestopper FS-60 system uses replacement remote: FSSK-60, CHX433TX

Note: All transmitter codes must be learned at time of programming!! The system learns up to 4 different transmitter codes.

1. Turn Ignition Key to the ON position. (Pink wire must be connected.)
2. Press Programming button 4 times. then after a few seconds the unit Chirps, Siren, Horn and Flashes the parking lights 4 times.
3. Press button #1 of the transmitter to be coded. You should get 1 Chirp/Honk indicating the first remote is coded, and then press
button #1 of a second transmitter, the unit will Chirp/Honk twice indicating the second remote is coded and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise tum key off.
4. The system will Chirp/Honk 4 times when exiting learning mode.
If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper FS-51 Remote Programming Instructions

This Crimestopper FS-51 system uses replacement remote: FSSK-50, Q6WBT0002

Please Read: The system can program a maximum of 4 remotes in it's memory. After programming your new remote you will need to reprogram the existing ones.

1. Twist the key in the ignition to ON position. (Don't start the engine and the pink wire must connected).
2. Press valet button 4 times, then the system will flash the parking lights 4 times.
3. Press the LOCK button then you should get 2 light flashes which means the remote has been programmed and waiting for a 2nd code.
4. If you have another remote, press the LOCK button on that remote, then the system will flash the lights 3 times indicating it's waiting for the 3rd code and so on. If all 4 remotes are programmed, the system will automatically turn the programming mode OFF, otherwise turn the ignition OFF to do it manually.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper FS-50 Remote Programming Instructions

This Crimestopper FS-50 system uses replacement remote: FSSK-50, Q6WBT0002

NOTE: All transmitter codes must be learned at time of programming!! These systems allow storage of up to 4 different remote codes in memory.

1. Turn key to the ON position. (Do not start the engine). Pink wire must be connected!
2. Press Program/Valet button 4 times, then a few seconds the unit flashes the parking lights 4 times.
3. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating it's waiting for the 3rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off. See diagram below.
If you can't find your valet switch click here.

Sunday, September 23, 2018

Crimestopper RS-830 Remote Programming Instructions

This Crimestopper RS-830 system uses replacement remote: CS-330TX, J5523518T1RSTX-3, VVJ-T612S434
and

INSTRUCTION: The system can program a maximum of 4 remotes in it's memory. After programming your new remote you will need to reprogram the existing ones.

1. Turn key to the ON position. (Do not start the engine). Pink wire must be connected!
2. Press Program/Valet button 4 times. Wait for the unit to flash the parking lights and/or honk horn exactly 4 times.
3. RS-3, RS- 4: Press button#1 (Lock) of the transmitter to be learned. 2-Way systems: Both the Lock & Unlock buttons must be pressed. You should get 2 light flashes and 2 horn honks indicating the code-learn. Now the unit is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 4 flashes after the 3rd code and 0 for 4th code.) If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper RS-1505DP Remote Programming Instructions

This Crimestopper RS-1505DP system uses replacement remote: CS-55TX, CHX433TX

Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system's remote codes must be learned at time of programming!! These systems aloow storage of up to 4 different remote codes in memory. The "Sidekcik" transmitters for the TW1/TW2 and FM systems are a special model that is not compatible with each other.

1. Open the hood (ground the blue pin wire if there's no hood pin installed.)
2. Twist the key in the ignition to ON position. (Do not start the engine) Pink wire must be connected!
3. Press the valet button 4 times. Wait for the system to flash the parking lights and/or honk horn exactly 4 times.
4. For 1-Way system: Press the LOCK button on the remote. 2-Way systems: Press LOCK and UNLOCK button at the same time. You should get 2 light flashes and 2 horn honks which mean remote have been programmed. Now the system is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 5 flashes for the 3rd code and 0 for 4th code.) If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF and close the hood.

If you can't find your valet switch click here.

Crimestopper RS-1405DP Remote Programming Instructions

This Crimestopper RS-1405DP system uses replacement remote: CS-55TX, CHX433TX

Attention: Your system can only save 4 remotes in it's memory. Make sure to reprogram your existing remote and program the new ones. This "Sidekick" transmitters for the TW1/TW2 and FM systems are a special model that is not compatible with each other.

1. Open the hood (ground the blue pin wire if there's no hood pin installed.)
2. Twist the key in the ignition to ON position. (Do not start the engine and pink wire should be connected).
3. Press the valet button 4 times. Wait for the system to flash the parking lights and/or honk horn exactly 4 times.
4. For 1-Way system: Press the LOCK button on the remote. 2-Way systems: Press LOCK and UNLOCK button at the same time. You should get 2 light flashes and 2 horn honks which mean remote have been programmed.
5. Now the system is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 5 flashes for the 3rd code and 0 for 4th code.)
6. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF and close the hood.

If you can't find your valet switch click here.

Crimestopper RS-3 Remote Programming Instructions

This Crimestopper RS-3 system uses replacement remote: RSTX-3, VVJ-T612S434

Your system can only save 4 remotes in it's memory. Make sure to reprogram your existing remote and program the new ones.

1. Open the hood (ground the blue pin wire if there's no hood pin installed.)
2. Twist the key in the ignition to ON position. (Do not start the engine and pink wire should be connected).
3. Press the valet button 4 times. Wait for the system to flash the parking lights and/or honk horn exactly 4 times.
4. For 1-Way system: Press the LOCK button on the remote. 2-Way systems: Press LOCK and UNLOCK button at the same time. You should get 2 light flashes and 2 horn honks which mean remote have been programmed.
5. Now the system is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 5 flashes for the 3rd code and 0 for 4th code.)
6. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF.

If you can't find your valet switch click here.

Crimestopper EZ-55DP Remote Programming Instructions

This Crimestopper EZ-55DP system uses replacement remote: CS-55TX, CHX433TX

Please Note: The system can program a maximum of 4 remotes in it's memory. After programing your new remote you will need to reprogram the existing ones. The "Sidekick" transmitters for the TW1/TW2 and FM systems are a special model that is not compatible with each other.

1. Open the hood (ground the blue pin wire if there's no hood pin installed.)
2. Twist the key in the ignition to ON position. (Do not start the engine) Pink wire must be connected!
3. Press the valet button 4 times. Wait for the system to flash the parking lights and/or honk horn exactly 4 times.
4. For 1-Way system: Press the LOCK button on the remote. 2-Way systems: Press LOCK and UNLOCK button at the same time. You should get 2 light flashes and 2 horn honks which mean remote have been programmed. Now the system is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 5 flashes for the 3rd code and 0 for 4th code.) If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF and close the hood.
If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Saturday, September 22, 2018

Crimestopper EZ-45DP Remote Programming Instructions

This Crimestopper EZ-45DP system uses replacement remote: CS-55TX, CHX433TX

Transmitter Programming:
Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system's remote codes must be learned at time of programming!! These systems aloow storage of up to 4 different remote codes in memory. The "Sidekcik" transmitters for the TW1/TW2 and FM systems are a special model that is not compatible with each other.

1. Open hood (ground the Blue pin wire if no hood pin is installed.)
2. Turn key to the ON position. (Do not start vehicle) Pink wire must be connected!
3. Press Program/Valet button 4 times. Wait for the unit to flash the parking lights and/or honk horn exactly 4 times.
4. 1-Way systems: Press button#1 (Lock) of the transmitter to be learned. 2-Way systems: Both the Lock & Unlock buttons must be pressed. You should get 2 light flashes and 2 horn honks indicating the code-learn. Now the unit is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes for the 2nd code, 5 flashes for the 3rd code and 0 for 4th code.) If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key OFF and close the hood.

If you can't find your valet switch click here.

Crimestopper CS-2004.DPII.TW2. Remote Programming Instructions

This Crimestopper CS-2004.DPII.TW2. system uses replacement remote: CHX433TX, CS-398FM, CS-398FMCF


Note: You're only allowed to program 4 remotes to this system. After programming the new remote you'll need to reprogram the existing once.

Follow steps below to program the new and existing remotes.

1. Twist the key in the ignition to ON position (don't start the engine) then press the valet button 4 times.
2. Parking lights flashes 4 times, siren chirps 4 times, horn honks4 times and LED light ON solid.
3. Press LOCK and UNLOCK button at the same time. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) which means the system/receiver is ready to program your 2nd remote. (If you only have 1 remote, just skip step 4 to 5 and perform step 6).
4. Press the LOCK and UNLOCK button on your 2nd remote, then the system/receiver will flash 3 times, 3 siren chirps and 3 horn honks. 
5. Press the LOCK and UNLOCK button on the 3rd or 4th remote. he system will not flash the lights when learning the 4th code.
6. Twist the key in the ignition to OFF position to turn programming mode OFF.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-2000.DPII.TW2 Remote Programming Instructions

This Crimestopper CS-2000.DPII.TW2 system uses replacement remote: CHX433TX, CS-398FM, CS-398FMCF

Attention: This system can save up to 4 remotes in it's memory. After programming your new remote you'll need to reprogram the existing once since the system will reset it's memory once it entered programming mode.

Perform the steps below to program your new and existing remotes.

1. Twist the key in the ignition to ON position then press the valet button 4 times.
2. Your system/receiver will flash the parking lights 4 times, siren 4 times, horn 4 times and status LED will turn on solid.
3. Press the LOCK and UNLOCK button at the same time.
4. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) which means the system/receiver is ready to program your 2nd remote. (If you only have 1 remote, just skip step 5 and 6 then do step 7).
5. Press the LOCK and UNLOCK button on your 2nd remote, then the system/receiver will flash 3 times, 3 siren chirps and 3 horn honks.
6. Press the LOCK and UNLOCK button on the 3rd or 4th remote. he system will not flash the lights when learning the 4th code.
7. Twist the key in the ignition to OFF position to exit programming mode.

If you can't find your valet switch click here.

Crimestopper CS-2000.DP.TW2 Remote Programming Instructions

This Crimestopper CS-2000.DP.TW2  system uses replacement remote: CHX433TX, CS-398FM, CS-398FMCF

Please Note: Make sure to reprogram your existing and new remote. And you can program up to 4 remotes to the system.

1. Turn the ignition ON and press the valet button 4 times.
2. The system will flash the parking lights 4 times, Siren 4 times, Horn 4 times and status LED will turn on solid.
3. Press the Button #1 (lock) and Button #2 (Unlock) together on the remote at the same time.
4. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) indicating the system is waiting for the second code to be programmed.
5. Press button #1 and #2 together of a second remote, the unit will flash 3 times, 3 siren chirps and 3 horn honks. Press the lock and unlock button on a 3rd or 4th transmitter for up tp 4 total. Note: The unit will not flash the lights when learning the 4th code. Turn key off to exit programming mode.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-2004.TW2.FM Remote Programming Instructions

This Crimestopper CS-2004.TW2.FM system uses replacement remote: CHX433TX, CS-398FM, CS-398FMCF 

TRANSMITTER PROGRAMMING

NOTE: All transmitter must be learned at the time of programming. This system can learn up to 4 remotes.

1. Turn key to the ON position and press button 4 times.
2. After a short delay, the unit will flash the parking lights 4 times, siren 4 times, Horn 4 times and status LED will be solid.
3. Press the Button #1 (lock) AND Button #2 (Unlock) together on the remote you wish to program.
4. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) indicating the unit is waiting for the second code to learn. Press button #1 and #2 together of a second transmitter, the unit will flash 3 times, 3 siren chirps and 3 horn honks. Press the lock and unlock button on a 3rd or 4th transmitter for up to 4 total.

Note: The unit will not flash the lights when learning the 4th code. Turn key off to exit programming mode.

If you can't find your valet switch click here.

Friday, September 21, 2018

Crimestopper CS-2000 II Remote Programming Instructions

This Crimestopper CS-2000 II  system uses replacement remote: CS-361TX, J5523518T1, M65NVTX464

PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) you should heard 3 chirps.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 5 siren chirps.
3 Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4 Repeat the steps above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD-2

TRANSMITTER PROGRAMMING Note: SYSTEM can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) You should hear (1) Short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode.
3. Press Button #1 on new transmitter-siren will chirp to confirm programming. Repeat step 3 within 5 sec. for up to 2 additional transmitters.
4. Turn off Ignition.

Note 2: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-9701 Remote Programming Instructions

This Crimestopper CS-9701  system uses replacement remote: CS-361TX, J5523518T1, M65NVTX464


PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) you should heard 3 chirps.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 5 siren chirps.
3 Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4 Repeat the steps above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD-2

TRANSMITTER PROGRAMMING Note: 
SYSTEM can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) You should hear (1) Short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode.
3. Press Button #1 on new transmitter-siren will chirp to confirm programming. Repeat step 3 within 5 sec. for up to 2 additional transmitters.
4. Turn off Ignition.

Note 2: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Thursday, September 20, 2018

Crimestopper CS-2000 Remote Programming Instructions

This Crimestopper CS-2000  system uses replacement remote: CS-355TX, J5523518T1CS-361TX, J5523518T1, M65NVTX464

This instruction works for 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

Please Note: These types of system can only keep up to 4 remotes codes in it's memory.

1. Turn the ignition ON and OFF 3 times from OFF position then leave it to the ON position.
2. Press the valet switch 5 times then light flashes 5 times and siren chirps 6 times.
3. Press #1 (LOCK) button on the remote twice for the 360, 336, 365, 366tx's and once for the regular TX.
4. Repeat the steps above to add another remote.
5. Turn the ignition off. Siren will chirp 3 times and lights flashe 3 times which means programming mode is OFF.

2ND METHOD

Perform all the steps below to program the remote: System can learn up to 3 different codes max.

1. Turn the Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (1) short chirp.
2. Push the Program/Override button for 5 seconds until the siren chirps (3) times. Release the button.
3. Press Button #1 on new transmitter - siren will chirp to confirm programming. Repeat Step 3 within 5 sec. for up to additional transmitters.
4. Turn the ignition OFF.

Note 1: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

NOTE 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) you should heard 3 chirps.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 5 siren chirps.
3 Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4 Repeat the steps above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD-2

TRANSMITTER PROGRAMMING Note:
SYSTEM can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) You should hear (1) Short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode.
3. Press Button #1 on new transmitter-siren will chirp to confirm programming. Repeat step 3 within 5 sec. for up to 2 additional transmitters.
4. Turn off Ignition.

Note 2: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-9601PI Remote Programming Instructions

This Crimestopper CS-9601PI  system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

THIS INSTRUCTION IS FOR ALARM SYSTEM:

1. The alarm system is usually installed under the dash.
2. Find and ground the White/Red Test mode wire.
3. Turn the ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch.
5. Press the 1st (Largest) Button on the remote. Siren will chirp which means the remote has been programmed.
6. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF.

THIS INSTRUCTION IS FOR REMOTE START SYSTEM:

1. Open the hood (Ground the hood pin wire if there's no hood pin found).
2. Turn the ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should turn itself on about a second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And in 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the brake pedal to clear the parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-830RKE Remote Programming Instructions

This Crimestopper CS-830RKE  system uses replacement remote: CS-355TX, J5523518T1CS-361TX, J5523518T1, M65NVTX464

NOTE: This system will learn a total of 4 remotes max and this instruction applies to: 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn the ignition ON and OFF 3 times quickly, leaving it ON the 3rd time.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 6 siren chirps.
3. Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4. Repeat the stpes above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: The System can only program a maximum of 3 and to program the remote

1. Turn the ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (1) short chirp.
2. Press the button for 5 seconds until the siren chirps (3) times. Release the button.
3. Press Button #1 on the remote then you'll hear a chirp. Go back to Step 3 within 5 sec. to program another remote.
4. Turn the ignition OFF.

Note 1: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system. Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) you should heard 3 chirps.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 5 siren chirps.
3 Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4 Repeat the steps above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD-2

TRANSMITTER PROGRAMMING Note:
SYSTEM can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) You should hear (1) Short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode.
3. Press Button #1 on new transmitter-siren will chirp to confirm programming. Repeat step 3 within 5 sec. for up to 2 additional transmitters.
4. Turn off Ignition.

Note 2: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

If you can't find your valet switch click here.

Crimestopper CAS-500EX Remote Programming Instructions

This Crimestopper CAS-500EX  system uses replacement remote: CS-355TX, J5523518T1CS-361TX, J5523518T1, M65NVTX464

PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 6 siren chirps.
3. Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4. Repeat the stpes above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD 2

TRANSMITTER PROGRAMMING NOTE: System can learn up to 3 different codes max.

1. Turn the Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (1) short chirp.
2. Push the Program/Override button for 5 seconds until the siren chirps (3) times. Release the button.
3. Press Button #1 on new transmitter - siren will chirl to confirm programming. Repeat Step 3 within 5 sec. for up to additional transmitters.
4. Turn off Ignition.

Note 1: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

NOTE 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

PROGRAMMING INSTRUCTIONS FOR 335, 336, 355, 361, 340, 341, 342, 360, 365, 366

1. Turn Ignition ON and OFF3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) you should heard 3 chirps.
2. Press the Program/Override button 5 times and you should hear 5 light flashes and 5 siren chirps.
3 Press #1 (lock) button on the remote 2 times for the 360-336-365-366tx's and 1 time for the regular TX.
4 Repeat the steps above for the second and 3rd Remote.
5. Turn off Ignition. Siren will chirp 3 times and lights will flash 3 times for exit confirmation.

NOTE: This system will learn a total of 4 remotes max.

METHOD-2

TRANSMITTER PROGRAMMING Note:
SYSTEM can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF,ON/OFF,ON) You should hear (1) Short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button. The system is now in programming mode.
3. Press Button #1 on new transmitter-siren will chirp to confirm programming. Repeat step 3 within 5 sec. for up to 2 additional transmitters.
4. Turn off Ignition.

Note 2: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and The system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.

Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-9605PI Remote Programming Instructions

This Crimestopper CS-9605PI  system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

PROGRAM STEPS FOR ALARM SYSTEM:

1. Locate alarm control module in vehicle. (Usually under driver's side of dash)
2. Locate and ground the White/Red Test mode wire.
3. Turn ignition on to the run position. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in test/programming mode.
4. Press and hold valet/override button (Red or Black momentary button mounted in vehicle).
5. Press the #1 (Larger) Button on the new transmitter.
6. The system will chirp and confirm code-learn. Repeat steps 4 & 5 for additional transmitters or proceed to next step.
7. Remove white/red wire from the ground, Turn off ignition, and test new remote(s).

Note: Most systems can learn up to 4 transmitter codes.

PROGRAM STEPS FOR REMOTE START SYSTEM:

1. Open hood (Ground hood pin wire if no hood pin is present in your installation).
2. Turn ignition on.
3. Press and hold brake pedal, then press program button until parking lights turn ON solid, (Parking lights should come on in about 1 second)
4. Release only program button.
5. With BRAKE still Depressed, Press and hold program button again.
6. Within 4 seconds press the button on the new remote you wish to be the remote start button.
7. Parking lights will flash once to confirm programming.
8. CLOSE HOOD FIRST, Then press and release BRAKE PEDAL to clear parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Wednesday, September 19, 2018

Crimestopper CS-9604 Remote Programming Instructions

This Crimestopper CS-9604  system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

There are two different instructions to program the remote. And most of them can only save up to 4 remotes in it's memory.

For Alarm System:
1. Look for the alarm system in usually installed under the dash.
2. Then find and ground the White/Red Test mode wire.
3. Turn ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch (Red or Black momentary button mounted in vehicle).
5. Press the 1st (Larger) Button on the remote.
6. You'll hear a chirp which means the remote has been programmed. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF, then test the remote(s).

For Remote Start System:
1. Open hood (Ground hood pin wire if there's no hood pin).
2. Turn ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should come on in about 1 second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And within 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the BRAKE PEDAL to clear the parking lights.

If you can't find your valet switch click here.

Crimestopper CS-9603DC Remote Programming Instructions

This Crimestopper CS-9603DC  system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Follow these instruction if you're programming the remote alarm system:

1. Locate alarm control module in vehicle. (Usually under driver's side of dash)
2. Locate and ground the White/Red Test mode wire.
3. Turn ignition on to the run position. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in test/programming mode.
4. Press and hold valet/override button (Red or Black momentary button mounted in vehicle).
5. Press the #1 (Larger) Button on the new transmitter.
6. The system will chirp and confirm code-learn. Repeat steps 4 & 5 for additional transmitters or proceed to next step.
7. Remove white/red wire from the ground, Turn off ignition, and test new remote(s).

Note: Most systems can learn up to 4 transmitter codes.

Follow these instruction if you're programming the remote start system

1. Open hood (Ground hood pin wire if no hood pin is present in your installation).
2. Turn ignition on.
3. Press and hold brake pedal, then press program button until parking lights turn ON solid, (Parking lights should come on in about 1 second)
4. Release only program button.
5. With brake still Depressed, Press and hold program button again.
6. Within 4 seconds press the button on the new remote you wish to be the remote start button.
7. Parking lights will flash once to confirm programming.
8. Close hood first, Then press and release brake pedal to clear parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-9601DA Remote Programming Instructions

This Crimestopper CS-9601DA system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Instructions for remote start system:

1. Open hood (Ground hood pin wire if there's no hood pin).
2. Turn ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should come on in about 1 second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And within 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the BRAKE PEDAL to clear the parking lights.

Instructions for alarm system:

1. Look for the alarm system in usually installed under the dash.
2. Then find and ground the White/Red Test mode wire.
3. Turn ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch (Red or Black momentary button mounted in vehicle).
5. Press the 1st (Larger) Button on the remote.
6. You'll hear a chirp which means the remote has been programmed. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF, then test the remote(s).

If you can't find your valet switch click here.

Crimestopper CS-9601CJ Remote Programming Instructions

This Crimestopper CS-9601CJ system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

NOTE: Most systems can learn up to 4 transmitter codes.

PROGRAM STEPS FOR REMOTE START SYSTEM:

1. Open hood (Ground hood pin wire if no hood pin is present in your installation).
2. Turn ignition on.
3. Press and hold brake pedal, then press program button until parking lights turn ON solid, (Parking lights should come on in about 1 second)
4. Release only program button.
5. With BRAKE still Depressed, Press and hold program button again.
6. Within 4 seconds press the button on the new remote you wish to be the remote start button.
7. Parking lights will flash once to confirm programming.
8. CLOSE HOOD FIRST, Then press and release BRAKE PEDAL to clear parking lights

PROGRAM STEPS FOR ALARM SYSTEM:

1. Locate alarm control module in vehicle. (Usually under driver's side of dash)
2. Locate and ground the White/Red Test mode wire.
3. Turn ignition on to the run position. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in test/programming mode.
4. Press and hold valet/override button (Red or Black momentary button mounted in vehicle).
5. Press the #1 (Larger) Button on the new transmitter.
6. The system will chirp and confirm code-learn. Repeat steps 4 & 5 for additional transmitters or proceed to next step.
7. Remove white/red wire from the ground, Turn off ignition, and test new remote(s).

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CS-9602PI Remote Programming Instructions

This Crimestopper CS-9602PI system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

REMOTE START SYSTEM:

1. Open the hood (Ground the hood pin wire if there's no hood pin found).
2. Turn the ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should turn itself on about a second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And in 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the brake pedal to clear the parking lights.

ALARM SYSTEM:

1. The alarm system is usually installed under the dash.
2. Find and ground the White/Red Test mode wire.
3. Turn the ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch.
5. Press the 1st (Largest) Button on the remote. Siren will chirp which means the remote has been programmed.
6. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF.

If you can't find your valet switch click here.

Tuesday, September 18, 2018

Crimestopper CAS-969DC Remote Programming Instructions

This Crimestopper CAS-969DC system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Instructions for alarm system:

1. Look for the alarm system in usually installed under the dash.
2. Then find and ground the White/Red Test mode wire.
3. Turn ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch (Red or Black momentary button mounted in vehicle).
5. Press the 1st (Larger) Button on the remote.
6. You'll hear a chirp which means the remote has been programmed. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF, then test the remote(s).

PROGRAM STEPS FOR REMOTE START SYSTEM:

1. Open hood (Ground hood pin wire if no hood pin is present in your installation).
2. Turn ignition on.
3. Press and hold brake pedal, then press program button until parking lights turn ON solid, (Parking lights should come on in about 1 second)
4. Release only program button.
5. With BRAKE still Depressed, Press and hold program button again.
6. Within 4 seconds press the button on the new remote you wish to be the remote start button.
7. Parking lights will flash once to confirm programming.
8. CLOSE HOOD FIRST, Then press and release BRAKE PEDAL to clear parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CAS-968PI Remote Programming Instructions

This Crimestopper CAS-968PI system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Program steps for alarm system:

1. Locate alarm control module in vehicle. (Usually under driver's side of dash)
2. Locate and ground the White/Red Test mode wire.
3. Turn ignition on to the run position. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in test/programming mode.
4. Press and hold valet/override button (Red or Black momentary button mounted in vehicle).
5. Press the #1 (Larger) Button on the new transmitter.
6. The system will chirp and confirm code-learn. Repeat steps 4 & 5 for additional transmitters or proceed to next step.
7. Remove white/red wire from the ground, Turn off ignition, and test new remote(s).

Note: Most systems can learn up to 4 transmitter codes.

Instructions for remote start system:

1. Open hood (Ground hood pin wire if there's no hood pin).
2. Turn ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should come on in about 1 second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And within 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the BRAKE PEDAL to clear the parking lights.

If you can't find your valet switch click here.

Crimestopper CAS-967DC Remote Programming Instructions

This Crimestopper CAS-967DC system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

ALARM SYSTEM:

1. The alarm system is usually installed under the dash.
2. Find and ground the White/Red Test mode wire.
3. Turn the ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch.
5. Press the 1st (Largest) Button on the remote. Siren will chirp which means the remote has been programmed.
6. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF.

REMOTE START SYSTEM:

1. Open the hood (Ground the hood pin wire if there's no hood pin found).
2. Turn the ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should turn itself on about a second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And in 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the brake pedal to clear the parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Crimestopper CAS-965PI Remote Programming Instructions

This Crimestopper CAS-965PI system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Instructions for alarm system:

1. Look for the alarm system in usually installed under the dash.
2. Then find and ground the White/Red Test mode wire.
3. Turn ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch (Red or Black momentary button mounted in vehicle).
5. Press the 1st (Larger) Button on the remote.
6. You'll hear a chirp which means the remote has been programmed. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF, then test the remote(s).

Instructions for remote start system:

1. Open hood (Ground hood pin wire if there's no hood pin).
2. Turn ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should come on in about 1 second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And within 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the BRAKE PEDAL to clear the parking lights.

If you can't find your valet switch click here.

Crimestopper CAS-963DC Remote Programming Instructions

This Crimestopper CAS-963DC system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

Instructions for alarm system:

1. Look for the alarm system in usually installed under the dash.
2. Then find and ground the White/Red Test mode wire.
3. Turn ignition ON. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in programming mode.
4. Press and hold the valet button/switch (Red or Black momentary button mounted in vehicle).
5. Press the 1st (Larger) Button on the remote.
6. You'll hear a chirp which means the remote has been programmed. Go back to steps 4 & 5 to add more remotes (maximum of 4).
7. Disconnect the white/red wire.
8. Turn the ignition OFF, then test the remote(s).

Instructions for remote start system:

1. Open hood (Ground hood pin wire if there's no hood pin).
2. Turn ignition ON.
3. Press and hold the brake pedal, then press valet button/switch until parking lights turn ON solid.(Parking lights should come on in about 1 second)
4. Release the valet button/switch.
5. With BRAKE still Depressed, Press and hold the valet button again.
6. And within 4 seconds press the button on the remote you're programming to be the remote start button.
7. Parking lights will flash once.
8. Close the hood first, Then press the BRAKE PEDAL to clear the parking lights.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.

Monday, September 17, 2018

Crimestopper CAS-962PI Remote Programming Instructions

This Crimestopper CAS-962PI system uses replacement remote: CS-333PI, CS-334DC, CHXPI9695

PROGRAM STEPS FOR ALARM SYSTEM:

1. Locate alarm control module in vehicle. (Usually under driver's side of dash)
2. Locate and ground the White/Red Test mode wire.
3. Turn ignition on to the run position. (Dash lights and buzzers) LED will turn solid for about 4 seconds indicating that the system is in test/programming mode.
4. Press and hold valet/override button (Red or Black momentary button mounted in vehicle).
5. Press the #1 (Larger) Button on the new transmitter.
6. The system will chirp and confirm code-learn. Repeat steps 4 & 5 for additional transmitters or proceed to next step.
7. Remove white/red wire from the ground, Turn off ignition, and test new remote(s).

Note: Most systems can learn up to 4 transmitter codes.

PROGRAM STEPS FOR REMOTE START SYSTEM:

1. Open hood (Ground hood pin wire if no hood pin is present in your installation).
2. Turn ignition on.
3. Press and hold brake pedal, then press program button until parking lights turn ON solid, (Parking lights should come on in about 1 second)
4. Release only program button.
5. With BRAKE still Depressed, Press and hold program button again.
6. Within 4 seconds press the button on the new remote you wish to be the remote start button.
7. Parking lights will flash once to confirm programming.
8. CLOSE HOOD FIRST, Then press and release BRAKE PEDAL to clear parking lights.

If you can't find your valet switch click here.

Carbine model PLUS-6900 Remote Programming Instructions

This Carbine model PLUS-6900 system uses replacement remote: ELVNTRFA, CA-RFLCD2

Attention: Your system will delete saved remotes from it's memory in chronological order once you forced it to program another remote while it's memory is full (systemcan only keep maximum of 4 remotes).

1. Turn the ignition ON.

2. Press the valet switch/button 3 times. Make sure you hear a chirp/beep.

3. Press the LOCK button on the remote until you hear a chirp/beep.

4. Go back to step 3 program additional remotes (maximum of 4).

5. Turn the ignition off or wait for 15 seconds for the system to turn programming mode OFF by itself. You should hear one short and one long chirps/beeps.

If your vehicle's system was installed without the valet switch you can order one and install it to make it easier to do the programming.